Buying Guides
EV Charging Cable Safety Standards: What to Check Before You Buy
On this page
An EV charging cable carries significant current for hours at a time and operates outdoors in all weathers. The difference between a well-made cable and a poor one is not obvious at first glance, but it matters. Here is what to look for.
The key standard: IEC 62196 and EN 50620
Two standards cover the components of a home EV charging cable:
- IEC 62196-2 (BS EN 62196-2): covers the Type 2 connector and socket. It defines the contact dimensions, the control pilot (CP) pin behaviour, the locking mechanism, and the environmental requirements. A connector that meets this standard fits any compliant Type 2 socket.
- EN 50620: the European standard specifically for EV charging cables. It covers conductor cross-section, insulation materials, temperature range, flexibility, and mechanical robustness. A cable built to EN 50620 is designed for the demands of repeated plugging, outdoor exposure, and sustained high current.
Cables sold in the UK and EU should meet both. If a product listing does not mention either standard, that is worth noting.
Conductor cross-section
The conductor is the copper wire inside the cable jacket. Its cross-section determines how much current it can carry safely without overheating.
- 2.5mm2: not suitable for 32A (7.4kW or 22kW) continuous charging. Acceptable only for lower-current applications.
- 4mm2: adequate for 32A single-phase (7.4kW) charging. Some manufacturers use 4mm2 for 7.4kW cables.
- 6mm2: required for 32A three-phase (22kW) charging, and specified by IEC 62196 for the phase conductors at that current level. Some premium 7.4kW cables also use 6mm2 for a cooler-running cable with more headroom.
A reputable seller will state the conductor cross-section. If a cable is priced very low for a 22kW rating, it is worth checking what conductor size is used.
Temperature range
EV charging cables operate outdoors year-round. EN 50620 specifies a temperature range of -30 degrees C to +50 degrees C for the cable jacket and insulation. This range covers UK winters reliably; below -30 degrees C (which does not occur in the UK), some cable jackets become brittle. A cable meeting this range remains flexible in a typical winter morning.
Control pilot wire
The Type 2 connector has a control pilot (CP) pin in addition to the power conductors. The CP pin carries a low-voltage signal between the charging station and the car that confirms the cable is connected, sets the maximum charge current, and allows the car to pause or stop charging. Without a functioning CP pin, most cars will not begin a charging session.
All properly made Type 2 cables have the CP wire included. Cables sold very cheaply occasionally omit it or wire it incorrectly, which causes the car to refuse to charge or charge at a very low rate.
Strain relief at the connectors
The points where the cable enters the connector bodies are the highest-stress points. Strain relief prevents the wires from being pulled, twisted, or bent sharply right at the connector - which is where failures start. Good strain relief uses a rubber or thermoplastic boot moulded over the cable entry. Poor strain relief uses only a cable tie or none at all.
Examine the connector end of any cable you are considering. The cable should enter the connector through a flexible sleeve that allows some movement without putting stress on the internal connections.
The locking mechanism
Type 2 connectors include a latch that engages the socket when plugged in, preventing the cable from falling out during a session. Some connectors also include a rotating collar that mechanically locks the connector into the socket and can only be released by rotating it. This is referred to as a cable lock.
A locking collar adds resistance to casual unplugging, which is a useful anti-theft measure. A connector without a locking collar relies solely on the socket's spring latch and the car's internal port-lock solenoid for retention.
Jacket material and UV stability
The cable jacket is typically made from a thermoplastic elastomer (TPE) or polyvinyl chloride (PVC). The best jackets are UV-stabilised to resist degradation from sunlight, oil-resistant for use on driveways, and flame-retardant. After several years of outdoor use, a jacket without UV stabilisation may crack or harden.
TPE jackets tend to remain more flexible in cold weather than PVC and are generally considered a higher-quality option for outdoor EV cables.
What to check before buying
- Certifications stated clearly: does the seller mention IEC 62196-2 and EN 50620, or at minimum CE marking?
- Conductor cross-section: 4mm2 or 6mm2 for 7.4kW; 6mm2 for 22kW.
- Temperature range: at minimum -30 degrees C to +50 degrees C.
- Control pilot included: a standard cable always has it; look for any mention of "CP wire included" or just check that the seller is a reputable UK or EU supplier.
- Strain relief visible: a product photo should show the cable entry point at the connector. If the photo is too small to tell, ask.
- Jacket material: TPE or UV-stabilised PVC for outdoor use.
Our view
The cheapest cables on a marketplace are often the ones where these specifications are absent or not tested. For a component that runs at 32A for eight hours overnight, we would not go below a cable that clearly states EN 50620 compliance and has 4mm2 or 6mm2 conductors. The cost difference between a basic and a well-made cable is small relative to the cost of the EV itself or the wallbox installation.
Frequently asked questions
Is CE marking enough to guarantee a safe cable?
CE marking indicates the manufacturer declares conformity with applicable EU/UK standards, but it is self-certified - not independently tested. It is a minimum bar, not a guarantee of quality. A cable with CE marking and stated compliance with EN 50620 and IEC 62196-2 from a named, established manufacturer is a stronger assurance than CE marking alone.
Can a poor-quality cable damage my car?
A defective cable could cause a charging fault, slow or stop a session, or in an extreme case overheat at the connection point. Modern EVs have onboard protection that monitors the control pilot signal and temperature; if either is outside acceptable limits, the car reduces or stops charging. This protects the battery but not necessarily the cable or the charger socket. Damage to a Type 2 socket on a car can be an expensive repair.
How long should an EV charging cable last?
A well-made cable used daily should last several years. The points most likely to fail are the connectors, particularly if the cable is frequently bent at the strain relief, dragged across rough surfaces, or left exposed to UV. Regular inspection for cracking, discolouration, or damage at the connector boots is good practice. If you notice a connector that is discoloured or runs noticeably warm during charging, stop using it and have it checked.
Should I buy from a UK seller?
Buying from a UK seller does not guarantee quality, but it makes returns and warranty claims straightforward. Look for a supplier that can point to test reports or stated compliance documentation for their specific products, rather than generic claims. Cables made to EU/UK standards and sold by an established UK business are your lowest-risk option.

Written by
Graham DoddCo-founder · drives a Volkswagen ID. Buzz
Graham drives a Volkswagen ID. Buzz and is happiest with it loaded up for a weekend away. Road trips, campsites and public AC points are his testing ground, so he knows first-hand why a cable needs to be the right length and easy to coil back into the boot.
More from GrahamKeep reading
More
charging guides.
Straight answers on connectors, charging speeds and what actually fits your car.
View all guides
Compatibility
How to Charge a Plug-in Hybrid (PHEV)
Charge a PHEV like any EV: use a Type 2 or Type 1 cable, and because the battery is small, a slow charger is often enough overnight. Most PHEVs use a Type 2 inlet; some older cars need Type 1 A 3-pin granny charger usually refills a small battery overnight Most PHEVs cannot rapid charge and rely on home AC charging

Compatibility
Can Two EVs Share One Charger?
Yes, two EVs can share one charger by charging in turn, splitting power, or using a dual-outlet unit. Sequential overnight charging suits most two-car homes Some smart chargers split power between two cars at once, more slowly A spare cable removes the hassle of swapping the lead between cars

How-to
How to Look After Your EV Battery
Keep the charge between 20 and 80% daily, moderate rapid charging, avoid temperature extremes and precondition in the cold. A middle charge band is gentlest for everyday driving Use rapid DC occasionally and home AC for regular top-ups Precondition the battery in winter and store at around 50 to 80%

How-to
Should You Charge Your EV to 100%?
For most EVs, cap daily charging around 80% and only fill to 100% before longer trips. Nickel based batteries prefer a daily limit near 80% to reduce wear Charge to 100% before long journeys when you need full range LFP batteries are usually fine charged to 100% regularly: check your handbook
